HealthShare

Syndicate content 57 

 

1. Scope and Objective:

 

Recently we supported a few NHS cases that required TIE (Trust Integration Engine) integration with the PKB service.   Hence this article is meant to be a 10-minute quick guide to describe a demo solution (simple configurations and end-2-end implementation steps) for Health Connect (Ensemble) Integration with PKB (Patient-Knows-Best) service.

+ 5   0 1
0

comments

596

views

+ 5

rating

If your application is raising <PROTECT> errors and you're finding it hard to work out why, here's a way to get additional information.

First, if auditing is not already enabled, turn it on:

Then use "Configure System Events" (highlighted above) and locate the event named %System/%Security/Protect. In the screenshot below I used the Filter field to do this (type "protect" - highlighted below - and press TAB):

Last comment 24 April 2017
+ 4   0 3
806

views

+ 4

rating

A sophisticated alerting solution lets you solve problems quickly and proactively.  Watch the recorded webinar: Proactive Alerting: Advanced Approaches for Alerting Solutions webinar presented by Michael Brady, InterSystems Technical Trainer, to learn how to make the most out of your alerting solution. 


Last comment 4 August 2017
+ 4   0 4
360

views

+ 4

rating

Amongst the large fonts and chunky icons of Portal's pages, the Menu button in the top left corner is easily overlooked:

When clicked, it often produces the following menu:

When I remember it's there, I find the "View Console Log" option particularly handy.

I wrote "often" above because I've also noticed that the Menu contents change when I'm on a page within the Ensemble section of Portal:

Last comment 14 February 2017
+ 4   0 3
249

views

+ 4

rating

Until recently I didn't pay much attention to Portal's home page:

If it's not showing when you initially launch Portal you can easily jump to it using the button / tab at the top of the left-hand column of options. And later during your session, get there via the Home link that will be visible at the top of every page.

On the Home page the "Recent" section is automatically maintained for you.

+ 3   0 1
0

comments

200

views

+ 3

rating

InterSystems is pleased to announce the availability of the following maintenance releases:

  • Caché and Ensemble 2016.2.3
  • HealthShare Health Connect v15.021 on core technology 2016.2.3

Caché and Ensemble 2016.2.3 are available on the same platforms as 2016.2.2

The full list of corrections can be found in the release notes.

+ 3   0 1
0

comments

183

views

+ 3

rating

User interfaces such as Portal often give us multiple ways of doing a task. Sometimes we stick with habits and don't realize that another way might save us time.

Here's one that I learned by watching someone else using Portal.

Use the Search box to get quickly to a page that may otherwise be several layers deep in the Portal hierarchy. For example, suppose I want to check the status of the ECP networking:

Last comment 14 February 2017
+ 2   0 3
170

views

+ 2

rating

HealthShare HealthConnect and Information Exchange version 15.03 support import transformations from C-CDA 2.1 to SDA. You can find these transforms in your installation's csp/xslt/SDA3 directory. For general information about import transforms, see "CDA Documents and XSL Transforms in HealthShare" in Overview of Health Connect.

Among the enhancements to import functionality added in connection with C-CDA 2.1 support is the ability to preprocess your C-CDA input files prior to the transformation done for import.

0   0 1
0

comments

532

views

0

rating

I needed to pass through a file with Ensemble but the operation wasn't writing some filenames as given because the  EnsLib.File.PassthroughOperation 'sanitizes' filenames removing characters that are not valid on some operating
systems;
09000655_AEDC_C3344059_A&#47;E_Martin Browne_09000655_201706221018.pdf
09000655_AEDC_C3344059_A#47E_Martin_Browne_09000655_201706221018.pdf

+ 1   0 2
0

comments

395

views

+ 1

rating

Hello guys,

I've got this piece of code which runs the method "WebMethod", that belongs to %SOAP.WebBase.cls.

It grabs the outcome from an internal webservice we have and after that, it writes into a file.

The thing is, when I browse the file contents, I realize that in the place where a special character should be, I see a question mark.

By querying the same webservice from a special soap tool called "SoapSonar" (I've been using this for years), the outcome shows up this special character (shows it properly).

Last answer 31 January 2017 Last comment 2 February 2017
+ 1   0 2
2685

views

+ 1

rating

Hello Greetings-

I am exploring on converting HL7 to FHIR.

1. I saw there are built in DTLs “FHIR.FromSDA” and “FHIR.ToSDA” to convert SDA -> FHIR and FHIR -> SDA. Similarly Do Intersystems have DTLs for HL7 -> FHIR and FHIR -> HL7?

2. The reason why I am asking is, I see in HSLIB namespace HS->GateWay->HL7->HL7toSDA3 and HS->GateWay->SDA3->SDA3toHL7 DTLs. Like-wise I am trying to locate HL7 -> FHIR and FHIR -> HL7. Please help me to locate them

Last answer 22 March 2017 Last comment 14 August 2017
+ 1   2 2
1046

views

+ 1

rating

InterSystems is pleased to announce the availability of the following maintenance releases:

  • Caché and Ensemble 2016.2.2
  • HealthShare Health Connect v15.021 on two core technology releases, 2016.2.2 and 2017.1.0

Caché and Ensemble 2016.2.2 are available on the same platforms as 2016.2.1

+ 1   0 1
0

comments

379

views

+ 1

rating

The class %Compiler.UDL.TextServices arrived in 2015.1, bringing us methods for exporting a class in UDL format (i.e. looking just like we're used to seeing it in Studio), and importing a UDL format definition back into a namespace. Some source control tools including our Deltanji are now able to use UDL format, resulting in diffs that are easier to understand.

Last comment 1 February 2017
+ 1   0 1
183

views

+ 1

rating

Hey all! I'd like to collect some feedback regarding searching for messages using the Message Viewer. I'd like to find out what things regarding the Message Viewer you all in the community have found difficult/confusing/poorly documented. This can of course include things that you don’t know how to do yet, but would like to learn about.

Last answer 2 May 2017 Last comment 1 May 2017
+ 1   0 0
247

views

+ 1

rating