#FTP

Hi,

I try SFTP connect by ObjectScript.
But occurred this error. Can't connect by SFTP key-pair authentication.

:ERROR #7510: SSH Error '-18': SSH Error [80101012]: Username/PublicKey combination invalid [80101012] at Session.cpp:458,0

Key pair was generate this way.
ssh-keygen -m pem -f ~/.ssh/id_rsa
"id_rsa" and "id_rsa.pub" is generated.
Passphrase is empty.

sftp command is connect successful.
ex.
sftp -i .ssh/id_rsa sftpuser@localhost

Hi all,

We are delivering files to SFTP server using EnsLib.FTP.PassthroughOperation class and EnsLib.FTP.OutboundAdapter. But we are facing error below:

ERROR <Ens>ErrFTPPutFailed: FTP: Failed to Put file '' (msg='Error in SFTP Put('/cachesys/mgr/Temp/HC4IZVmI6w9gEw.sftp','/directory1/directory2/directory3/') ERROR #7511: SFTP Error '4': SFTP Error [80102004]: Operation Failed [80102004] at SFTP.cpp:750,0',code=0).

The SFTP settings is as follows:

Basic settings:

Hello,

I have been facing a problem for several months, I have several flows that work in SFTP with the iris class EnsLib.FTP.PassthroughService

The problem is that from time to time I get an error message that says:

"A connection could not be established because the target computer expressly refused it"

I had the case for a server at our house and we solved the problem by extending the call interval parameter to 60 seconds,

Hello,

I have a EnsLib.HL7.Operation.FTPOperation that uses SFTP protocol and public/private key to connect to an external vendor moveitcloud.

Issue: The vendor is planning to enable Multi Factor Authentication for this file transfer account.

Question: Have you configured a SFTP operation to use Multi factor Authentication? If not, is there another way?

Thank you,

Morning everyone,

I would appreciate some advice please- hopefully there is plenty of experts out there.

We are setting up an sFTP share between hospital trusts here in the UK and I have set the outbound operation up using a custom extension of EnsLib.HL7.Operation.FTPOperation.

We are configuring a VPN tunnel to run between the sites also so there is a bit of firewall / network routing to take place to enable the connection but to add in a complication we are on a mirrored cluster and usually present on a Virtual IP address.

Good Afternoon My InterSystems IRIS Peers,

I have the following issue that I need help with, I tried all possibilities that I know of, therefore I am reaching out to the community for some insight.

I have a SFTP service that pulling 2.5.1 DFT HL7 messages from our SFTP file server. The issue is that IRIS is transforming patients names and addresses that contain special chars UTF-8 to ANSI.

Examples:

è = è
é = é
í = í- .......etc

In 2020 we implemented HealthConnect as our HL7 interface engine. Having completed this, we are currently evaluating whether it would be beneficial to migrate our managed file transfers from our current MFT software, MOVEit to HealthConnect. I am interested in hearing from any InterSystems customers who have previously used MOVEit and currently using HealthConnect for file transfer managment. Any feedback would be appreciated.

Does anyone know about any documentation or sample code to create SFTP Business service in HealthShare?

Thank you for your help.

Hi community,

I am now working with an ftp adapter. I have no problem connecting to the FTP server, but there are problems with interacting with files. Has anyone had any experience with an FTP adapter, such as getting/modifying/deleting files?

Good morning all,

A question to see if anyone out there is already doing this.

We have built a custom BS based off of the EnsLib.FTP.InboundAdapter. We have our processes wake up (using the Scheduler), grab the files in the directory, stay awake for a while, and then go back to sleep.

Each file goes through on its own message. So we can trace each individual file and we know if it made it successfully or not.

I have a service named FTP_In that is of class EnsLib.HL7.Service.FTPService. It picks up files from multiple subfolders and sends them to an EnsLib.HL7.MsgRouter.RoutingEngine. What I want to do is somehow capture the subfolder as a variable for use in the routing rules. Is this possible?

Let's say I have the following files and directory structure on my FTP Server

Hello,

I'm trying to upload file to SFTP server.

I have access to SFTP server .
My code is bellow

Try {
Set sftp = ##class(%Net.SSH.Session).%New()

I have been using %Net.FtpSession and while it works, its handling of file/directory listings from an FTP server is less than ideal and, while this is due to the FTP protocol itself, the class could be written to handle this as would an FTP client such as FileZilla and command line/class FTP handlers for other languages. I was wondering if anyone knows how the Ensemble adaptor works with this in case it provides code that would help, though the source does not seem to be available. Below are the issues I see in FTP, some are based on past experience writing our own FTP handler in the past

TL;DR: If I set an Ensemble Production Service based on EnsLib.File.PassthroughService to a Binary charset encoding, it breaks the file handling. Any ideas?

Full long post:

All,