Out of sequence Z segments in HL7
Hi- I have a HL7 message ADT_A01 (Admit) that contains several Z segments, which don't necessarily all appear at the end of the document, like normal. See below...
1 MSH ^ ~|\& ^ VAFC PIMS ^ 500 ^ HEALTHSHARE ^ 500 ^ 20171103154747-0500 ^ · ^ ADT ~ A01 ^ 50019000 ^ T ^ 2.3 ^ · ^ · ^ · ^ NE ^ USA
2 EVN ^ A01 ^ 20171103154701-0500 ^ · ^ 05
3 PID ^ 1 ^ 5000000351V802052 ^ 100853 ~ 1 ~ M10 ^ 3333 ^ POINDEXTER ~ KENNETH ^ "" ^ 19690117 ^ M ^ · ^ "" ~ · ~ 0005 ~ "" ~ · ~ CDC ^ "" ~ "" ~ "" ~ "" ~ "" ~ · ~ P ~ "" ~ "" | "" ~ "" ~ "" ~ "" ~ "" ~ · ~ VACAE ~ "" ~ "" ~ · ~ · ~ "" & "" | "" ~ "" ~ "" ~ "" ~ "" ~ · ~ VACAA ~ "" ~ "" ~ · ~ · ~ "" & "" | "" ~ "" ~ "" ~ "" ~ "" ~ · ~ VACAC ~ "" ~ "" ~ · ~ · ~ "" & "" | "" ~ "" ~ "" ~ "" ~ "" ~ · ~ VACAM ~ "" ~ "" ~ · ~ · ~ "" & "" | "" ~ "" ~ "" ~ "" ~ "" ~ · ~ VACAO ~ "" ~ "" ~ · ~ · ~ "" & "" ^ · ^ "" ^ "" ^ · ^ "" ^ 29 ^ · ^ 555443333 ^ · ^ · ^ "" ~ · ~ 0189 ~ "" ~ · ~ CDC ^
4 PD1 ^ · ^ · ^ CAMP MASTER ~ · ~ 500 ^ ""
5 ZPD ^ 1 ^ "" ^ "" ^ "" ^ "" ^ "" ^ "" ^ "" ^ "" ^ "" ^ 0 ^ "" ^ "" ^ "" ^ "" ^ 0 ^ "" ^ 0 ^ "" ^ "" ^ ""
6 PV1 ^ 1 ^ I ^ 7B ~ "" ~ "" ^ · ^ · ^ · ^ 1002 ~ PROVIDER ~ EIGHTEEN ^ · ^ · ^ 94 ^ · ^ · ^ · ^ · ^ · ^ · ^ · ^ EMPLOYEE ^ · ^ · ^ 1 ^ · ^ · ^ · ^ · ^ · ^ · ^ · ^ · ^ · ^ · ^ · ^ · ^ · ^ · ^ · ^ · ^ · ^ · ^ · ^ · ^ · ^ · ^ 20171103154701-0500 ^ "" ^ · ^ · ^ · ^ · ^ 13976
7 ROL ^ 13976-1002*1 ^ CO ^ V110000 ~ Physicians (M.D. and D.O.) & Physician/Osteopath & "" ~ VA8932.1 ~ T ~ "" ~ VA01 ^ 1002 & 500 ~ PROVIDER ~ EIGHTEEN ~ "" ~ "" ~ "" ~ "" ~ VA200 | "" ~ "" ~ "" ~ "" ~ "" ~ "" ~ "" ~ "" ~ SSA
8 ROL ^ 13976-991*2 ^ CO ^ V110000 ~ Physicians (M.D. and D.O.) & Physician/Osteopath & "" ~ VA8932.1 ~ A ~ "" ~ VA01 ^ 991 & 500 ~ PROVIDER ~ EIGHT ~ "" ~ "" ~ "" ~ "" ~ VA200 | "" ~ "" ~ "" ~ "" ~ "" ~ "" ~ "" ~ "" ~ SSA
9 DG1 ^ 1 ^ · ^ · ^ PSYCHOSIS
10 ZSP ^ 1 ^ 0 ^ "" ^ "" ^ "" ^ "" ^ "" ^ "" ^ · ^ "" ^ ""
11 ZEL ^ 1 ^ "" ^ "" ^ "" ^ "" ^ "" ^ "" ^ 0 ^ EMPLOYEE ^ "" ^ "" ^ "" ^ "" ^ "" ^ "" ^ "" ^ "" ^ "" ^ "" ^ "" ^ "" ^ ""
12 ZCT ^ 1 ^ 1 ^ "" ^ "" ^ "" ^ "" ^ "" ^ "" ^ ""
13 ZEM ^ 1 ^ 1 ^ "" ^ "" ^ "" ^ "" ^ "" ^ "" ^ ·
14 ZIR ^ ·
15 ZEN ^ 1
My HL7 Router is sending this message to the bad message handler even though my Validation setting on the router is 1. It's complaining because there is a Z segment that appears before the PV1 segment. I have no control over the source system and am wondering if there is any way to have this message go through as-is without having to create a custom schema?
If I need to, I can create the custom schema, however, would like to not have to do that if there is a way to just have this message go through without it.
Thanks